Zebralight H600w MK2 XHP35 Neutral White Headlamp

작성일: 2017.11.15

---------------------------------------------------

Zebralight H600w Mark3 입니다.

LED는 Cree사의 XHP35를 채택한 제품이며, 작성일 기준 현재 Mark4를 출시하였고 선주문 접수 중이네요.

우선 제조사의 제품 사양입니다.

LED: Cree XHP35 Neutral White (Nominal CCT 4500K)

User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.

Light Output (runtimes)

High:         H1 1126 Lm (PID, approx 2.2 hr)   or    H2  580 Lm (PID, approx 2.8 hrs) / 312 Lm (4.3 hrs) / 139 Lm (12 hrs)

Medium:    M1 61 Lm (33 hrs)    or    M2   28 Lm (73 hrs) / 10 Lm (8 days)

Low:         L1   3.3 Lm (18 days)   or    L2   0.37 Lm (2.8 months) / 0.05 Lm (5.1 months) / 0.01 Lm (7.1 months)

Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1

 

Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using ZL634 batteries. Runtimes of the two PID controlled levels (1126Lm and 580Lm) vary greatly with ambient temperature and air circulation.

Operating Voltage Range: 2.7V - 6.0V

Battery: One 18650 size (up to 69mm long) 3.6V-4.35V li-ion rechargeable. Batteries are not included in the package.

Parasitic Drain: Negligible (much less than the self discharging of a battery)

Beam Type

 80 degree spill

 12 degree hot spot

Dimensions

 Head Diameter: 0.95 inch (24.2 mm)

 Length:    3.85 inch (97.8 mm)

Weight

 1.4 oz (39 gram) 

 3.0 oz (84.6 gram) with ZL634 battery

 4.4 oz (124.6 gram) with ZL634 battery and headband

Features

 PID thermal regulated outputs (1126Lm and 580Lm)

 Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)

 Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low

 Builtin over-discharging protection (2.7V cutoff)

 Durable electronic soft-touch switch

 Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.

 Precision machined unibody casing from premium grade  aluminum bar stocks

 Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing

 Durable natural hard anodized finish (Type III Class I)

 Sealed and potted LED driver circuitry

 Battery reverse polarity protection

 Tempered optical grade glass 

 Orange peel textured reflector

 Waterproof to IPX8 (2 meters, 30 minutes)

Operations

This light has 3 main levels (High, Medium, and Low) and a beacon-strobe mode. Each main level can be programmed to one of its two sub-levels. The second sub-level of each main levels can be further programmed to different brightness levels.

Basic Operation

 One short-click turns on the light to High or turns off the light.

 Two short-click turns on the light to Medium.

 Three short-click turns on the light to the beacon-strobe mode.

 Press and hold (for over 0.6 seconds) turns on the light to Low and then Medium and High. Release at the desired level.

Advanced Operation and Configuration

 Press and hold to cycle from Low, Medium and High, release at the desired level to set. When press and hold, the light always cycle from Low to High regardless which level you are currently in.

 Double click to toggle and select between the two sub-levels for that main level. Sub-level selections for the 3 main levels are memorized after the light is turned off and through battery changes.

 The second sub-level (H2, M2 and L2) of each main levels can be further programmed to different brightness levels. At a main level, double-click 6 times to start configuration. On subsequent double-clicks the light will cycle through different brightness levels. Short click to turn off the light when finishing configurations. The selections for the second sub-levels are memorized after the light is turned off and through battery changes.

 This light uses the main LED (flashing 1 to 4 times) to indicate the estimated remaining capacity of the battery. To start the battery indicator, (from Off) short-click 4 times without pause.

 Beacon-strobe mode can be accessed from 3 short-clicks when the light is Off. Once in the beacon-strobe mode, you can double-click to cycle through different types of beacons and strobes. Beacon-strobe settings are memorized when the light is turned off and through battery changes.

 

Accessories in the package

Two o-rings

Headband with removable top strap, and a black silicone holder

제품 포장은 갈색 종이박스입니다.

구성품

헤드밴드입니다.

Armytek Wizard, Olight H2R의 경우 헤드밴드에 라이트를 고정하는 방식이 제브라라이트와 달리 탈부착이 손쉬운 형태로 나오는데요.

제브라라이트는 탈부착은 어렵지만 확실하게 고정할 수 있는 형태입니다.

두개의 고무링 사이로 라이트를 집어넣는 형태입니다.

쥐색 아노다이징은 이전 제품들과 동일합니다.

Mark2와 달라진 점은 몸체 디자인이며, Mark2는 몸체 전부 주름이 있었다면 Mark3는 테일캡쪽만 주름이 있다는 정도입니다.

주름 대신 밋밋한 형태로 바뀐 부분

테일캡쪽만 주름이 있으며, 테일캡은 이전과 같이 직선형 널링이 있습니다.

헤드쪽 방열핀

뒷면

전면 유리에는 AR코팅은 안된 것으로 보입니다. 

제품 가격 생각하면 AR코팅이 없다는 건, 감점 요인이네요. (물론 AR코팅이 밝기에 크게 영향을 줄 정도는 아니며, 실사용할 때 문제는 없습니다.)

OP반사경이며, 뉴트럴화이트 LED라는 약간 더 노란색입니다.

테일캡

헤드 쪽 전자식 스위치

테일캡만 분리됩니다.

최근에 Zebralight 제품들은 Pogo Pin을 채택하면서 크기를 확 줄였는데요.

반대급부로 비보호 18650 배터리만 사용해야한다는 점이 있습니다. (SC600 Mk3, Mk4, SC63, SC64 류) 다행히 헤드램프에는 Pogo Pin을

적용하지 않고 있으며, 아래 사진처럼 테일캡에는 스프링이 부착되어 있습니다.

나사선도 잘 가공되어 있구요.

헤드쪽에도 스프링이 있습니다.

한 손에 쥐기 딱 적당한 크기입니다.

아래는 빔샷입니다.

실내빔샷 (거리 약 50cm)

H1

H2 (580lm)

M1

M2 (28lm)

L1

실외빔샷 (거리 약 5m)

H1

H2 (580lm)

M1

M2 (28lm)

구입하고 서랍속에 보관하다보니 어느새 Mark4가 나왔네요...