본문 바로가기

Flashlight/Review

OVEREADY TORCHLAB L3N XP-G Neutral White

작성일: 2016.08.13

-----------------------------------------------------------------------------------------------------------------------------------------------------------


Oveready라는 미국의 커스텀라이트 제조사에서 만든 Torchlab L3N 입니다.

중고로 구입한거라 정확한 spec.은 찾기가 어렵네요.

판매자는 L3N XP-G 라고 해서 CPF 나 구글링 해본 결과로는 v3.1 버전이고

LED 는 XP-G Neutral White

Mode는 Low(1%)-Med(30%)-High(100%) 이며, 아마도 최고 10W 급으로 보입니다.


아래는 Oveready 홈페이지에서 퍼온 자료입니다.

V4 WASP Head인데, 아래쪽에 보면 V3.1 부터의 개요와 명명방식에 대한 소개가 있습니다.

(원본주소: http://www.oveready.com/moddoolar/moddoolar-head-triple-v4-wasp-15w-/prod_221.html)


MODDOOLAR HEAD TRIPLE V4 WASP (15W)

Moddoolar Head Triple v4 Wasp (15w)

PRODUCT INFORMATION

Moddoolar Head Triple H3 Wasp

Control the Dark. Simplicity, performance, reliablitiy - in one tiny package

World's only open airflow flashlight:

 

Custom molded self charging (GID) optic frame:

 

 Operation:

  • 3 mode operation: high -> medium -> low -> high -> medium -> low ->
  • Turn power off, then on again within 3 seconds to change to the next level
  • Turn power off, then on again after 4 seconds to reset back to high
  • Automatically resets to high after power cycle exceeding 5 seconds (off/on) or battery change
  • Available in one of two mode sequences, HML or LMH:


  

 

Advantages:

  • Shock isolated UCL glass lens (window)
  • Integrated 304 grade stainless steel protective bezel ring
  • Body + Head + Tail  vs  Bezel + Drop in + Throat + Body + Tail
  • 3/8 inch shorter than equivalent 18mm P60 based setups:

 

 

Construction:

  • Hard anodized finish for superior thermal emissivity and durability
  • Shock and vibration tolerant materials and components
  • Gold plated copper contact surfaces
  • Silver plated berryllium copper spring
  • Shock proof materials, components, and design
  • 22 gauge mil-spec wire with 19 strand, silver-plated copper conductors, teflon insulated

  

 

Design:

  • Fully regulated output between 4.8 and 9.5 volts
  • Below 4.8v it drops out of regulation and continues running until about 3v
  • Cell count detection and monitoring
  • Output reduces to 10% at 3.4V (10% capacity remaining)
  • Battery protection cuts all output at 3.0V
  • Mode changes have a subtle transition effect (brief soft shifting)
  • Mode changes allow button presses as fast a 1/4 of a second
  • 93% efficient driver with 2 lithium ion cells
  • Thermally-Enhanced Metal Core PCB
  • Integrated thermal safety protection at 65C (149F)
  • Integrated thermal overheating protection at 120C (248F)
  • Shock proof materials, components, and design
  • Suitable for use in weapon mounted lights
  • Multiple independent LEDs for more output than single LED designs (even at the same wattage)

 

Configurations:

Choose Nichia 219B for smooth beam and best color rendition

900 lumens:

  • TL35 with 1x18350
  • TL50 with 1x18500
  • TL65 with 1x18650

1300 lumens:

  • TL65 with 2x18350
  • TL100 with 2x18500
  • TL130 with 2x18650

 

Choose CREE XPL for maximum output and tigher beam

1300 lumens:

  • TL35 with 1x18350
  • TL50 with 1x18500
  • TL65 with 1x18650

2100 lumens:

  • TL65 with 2x18350
  • TL100 with 2x18500
  • TL130 with 2x18650

  

Optional Trit Slots

6 linear cut Trit slots (2 x 8mm trits available here)

 

Power Levels:

Run from 2 cells, total current to the LEDs is fully regulated and does not change while the cells drain:

  • High 4500mA
  • Medium 1350mA (30%)
  • Low 45mA (1%)


Run from a single cell, total current to the LEDs is about 30% lower and will change some as the cell drains:

  • High 3000mA
  • Medium 900mA
  • Low 30mA

Notes:

  • Competitor amp values are usually power from the battery.  All values above are power to the LEDs.
  • Competing configurations loose considerable power in the driver, reducing potential output
  • Single cell values are approximate and dependent on the voltage sag of the particular cell being used

 

Recommended Switches:

  • Surefire Z41 with SF Twisty or Zero Rez or ZRS or McClicky
  • Moddoolar Triad with SF Twisty or Zero Rez or ZRS or McClicky
  • Zero Rez does not increase output
  • McClicky's should be MEDpress or HARDpress with unsheltered boot (ie, Z41)


CAUTIONS:

  • Do not leave unattended while running on high
  • Do not run primary CR123 on high (100%). The boost driver will drain them harder and harder until the cells overheat, and may explode.
  • IMR18350 are recommended minimum. 
  • This light creates excessive heat
  • This light may cause eye damage
  • This light may burn the skin at close range
  • This light may cause combustibles to ignite
  • This light is not a toy, keep away from children

 

MODELS:

Name                   Voltage      2cell (1cell)*       Modes       Tint

Triple/Mod H3        1-2 cells     2100L (1300L)        H-M-L        XPL

Triple/Mod H3n        1-2 cells     1300L (900L)        H-M-L      Neutral 219 (4500K)

 * Lumen outputs are LED rated values based on power, out the front values will be less

 

Universal Name KeyLEDcount / Format [space] Power Modes Tint
      (not all options available on all models or formats)

LEDcount: 1 (single) or 3 (triple)
Format: 60 (drop in) or Mod (head)
Power: L (10w) or H (15w)
Modes: 1 (high) or 3 (high, medium, low)
Tint: C (cool) or N (neutral) or W (warm)

 

Version History

  • 4.00 - add H (15w) model
  • 4.00 - add cell count detection (1 or 2)
  • 4.00 - add low voltage reduction (10% at 3.4v per cell)
  • 4.00 - add low voltage cutoff (0% at 3.0v per cell)
  • 4.00 - add thermal protection (10% at 65C)
  • 3.10 - add reverse cell protection
  • 3.10 - reduce intervals for mode changes & resets
  • 3.10 - add brief softstart to each mode
  • 3.10 - first version 

Oveready에 사용된 Triple LED light engine은 LED칩과 회로가 같이 있는 일체형 제품으로 Oveready에서 만든 제품은 아니고 

러시아의 Lux-RC라는 곳에서 만든 것을 가져다가 조립하고 있습니다.


아래처럼 생겼습니다. (구형입니다. L333)


아래는 최신형인 371D (XP-L HD의 돔을 제거하여 다시 reforming한 것이며, "371" 숫자가 새겨진 부분에 있는 작은 2nd LED가 있습니다.

색상은 적색 or 황색이 있죠. 


현재 Oveready에서 팔고 있는 V5 헤드 및 Moddoolar 라이트에 사용되는 것과 동일합니다.


사전 설명이 길었네요.

구입한 제품은 검정색이고, 테일캡은 Triad tailcap입니다.

몸체는 1*18650 or 2*18350 배터리를 사용할 수 있는 TL65 입니다. 





헤드에 있는 TORCH LAB 각인




커스텀 제품이라서 부품 하나 하나가 옵션이고 가격도 높습니다.

Triad Tail cap 기본 가격이 $60 입니다.

기본적인 슈어파이어 트위스트 테일캡을 기본으로 포함되어 있는데 이 가격이 $4 이어서 최소 $64부터 시작합니다.

McClicky switch로 바꾸면 $22 

Clip 선택 시 $26

총 $60+$22+$26 = $108 이라는 가격이 나옵니다. 

여기에 테일캡에 Tritium Vial을 장착할 수 있는 테일캡으로 선택할 수 있어서 금액이 계속 높아지죠.



어쨌든 가격이 높은만큼 만듦새도 괜찮습니다.


몸체에 각인된 TL65 MADE IN USA

배터리 길이에 따라 옵션은 다양합니다.

TL34 -> 16340, 18350, 18500 (단, ZRS라는 부품을 사용하는 경우)

TL50 -> 18500, 14500, AA, 17500, 18650 (단, ZRS 사용 시)

TL1450 -> 14500, AA 배터리 전용 (직격이 TL50에 비해 좁음)

TL65 -> 1*18650, 2*16340, 2*18350, 1*16650, 1*17670

TL100 -> 2*18500, 2*14500, 2*17500, 2*AA

TL130 -> 2*18650

추가적으로 TLXX-S 라고 표기된 경우가 있는데, 이는 Slim body를 뜻합니다.



AR코팅된 유리 파란색과 보라색이 섞인 색상입니다.


전면부

반사경이 아닌 optic lens 방식이며, Carclo 10507 Clear Narrow 입니다.

베젤은 분해가능합니다.


기본 분해


헤드쪽 모습

어떻게 아래과 같이 만든 것인지 신기하더군요. 정말 깔끔합니다.


테일캡쪽에는 오링이 2개입니다.


헤드쪽


헤드쪽입니다.


테일캡쪽


스위치는 McClicky입니다.


배터리를 넣은 모습


몸체 안쪽에 배터리에 가해지는 충격을 흡수하기 위한 오링이 하나 들어가 있습니다.


헤드도 무거운 편이라서 손에 쥐면 묵직합니다.


테일캡 전류 측정 (배터리는 LG HG18650 3000mAh 사용, 비보호)

Low


Medium


High


실내빔샷 (거리 약 50cm, ISO 100, 태양광, 1/250s)

Low


Medium


High


실외빔샷 (거리 약 5m, ISO 100, 태양광, 1s)

Medium


High


원거리빔샷

High


예전부터 한 번은 보고 싶었던 Oveready 제품인데, 확실히 잘 만든 제품이고, 해외에서 인기가 있는 이유를 알 것 같습니다.

다만, 가격이 높아서 망설여지는 점은 어쩔 수 없는 것 같습니다.


지금은 최신형으로 나온 V5 WASP Moddoolar 라이트 제품의 경우 약 $400 정도 합니다. 물론 그럼에도 인기가 많아서 현재는 재고가 없는 상태죠.



(사진 출처: 링크클릭)